How do I factory reset a Cisco AP?

Posted on by Mary Andersen

How do I factory reset a Cisco AP?

Reset Cisco Wireless AP to factory defaults

  1. Connect the console cable.
  2. Unplug the power or network cable if connected to a POE switch.
  3. Press and hold the Mode button.
  4. Plug the power back into the AP.
  5. Wait until the output on the console says button is pressed.

How do I reset my access point settings?

Press and hold the Reset button of your access point for 30 seconds. Once the access point is reset, perform a powercycle….

  1. Open the access point’s web-based setup page. For instructions, click here.
  2. Click the Administration tab and then click on the Factory Defaults sub-tab.
  3. Click Restore All Settings.

How do I reset my Cisco Aironet 1200 to factory settings?

Factory Reset via MODE Button Press and hold the MODE button while you reconnect power to the access point. Hold the MODE button until the Status LED turns amber (approximately 1 to 2 seconds), and release the button.

How do I reset my Cisco access point 2702?

Here is the procedure:

  1. Disconnect power from the AP or Disconnect the power jack for external power or the Ethernet cable for inline power.
  2. Press and hold the MODE button while you reconnect power to the AP.
  3. Hold the MODE button until the Status LED turns amber, and then release the button.

How do I reset my Cisco router password without losing the configuration?

Reboot the router using the power switch. Press BREAK on the console terminal. When rommon>1 appears on the screen enter confreg 0x2142 comand to restart from the flash (This step skips the start-up configuration where the passwords are stored). Enter the RESET command when rommon2 > appears on the display.

How do you reset a cisco switch physically?

Manually Reset the Switch Step 1. Disconnect all Ethernet cables from the switch. Step 2. Using a pin, press and hold the Reset button on the switch for 15 to 20 seconds.

What is Mode button on cisco switch?

Mode Button is used in combination with the port LED’s for checking the status of ports. It is also used to check the utilization on the switch etc. However, they are not the easiest of indicators to remember. So, Its most useful feature is about password recovery of the Enable mode Passwords.

How do I reset my Cisco WAP4410N to factory settings?

How to factory reset (hard reset) Cisco WAP4410N :

  1. When the router is on, press the button reset and hold for 30 seconds.
  2. While holding down the button reset, turn off the power of the router and hold down the button reset for 30 seconds.

How do I log into my cisco access point?

The default username is Cisco. Step 4 Enter the access point password in the Password field and press Enter. The default password is Cisco. The Summary Status page appears.

How do I find my Cisco AP IP address?

To find the Access Point’s IP address

  1. Open utility window, make sure Get IP addr is selected in the Function box.
  2. Type the Access Point’s MAC address in the Device MAC ID field.
  3. Click Get IP Address.
  4. Write down the Access Point’s IP address that appears in the IP Address field.

How do I reset my ROMmon password?

Type reset at the rommon 2> prompt. Type no after each setup question or press Ctrl+C to bypass all questions. Type configure memory or copy startup-config running-config in order to copy NVRAM into memory. Type enable secret in order to change the enable secret password.

How do I restore a cisco switch using putty?

Ensuring that any Windows firewall is OFF.

  1. Launch Putty and point it at 10.0.0.3 using Telnet.
  2. The prompt should show “switch#”
  3. Wait a good few minutes.
  4. After about 10 minutes power cycle the switch.
  5. When it comes back up it should be as the production switch.

Where is Mode button?

The MODE button (see the image below) is the left one of the two buttons between the mode dial and the command dial.

How do I access the console port on a Cisco 1100 router?

Cisco 1100 series routers have console port with modem support. The following sections describe the main methods of accessing the router: The CON port is an EIA/TIA-232 asynchronous, serial connection with no-flow control and an RJ-45 connector. The CON port is located on the front panel of the chassis.

How do I Reset my Cisco Aironet Wireless access point?

Posted in Cisco Wireless Resettinga Cisco Aironet access pointcan be required if you’ve lost your password or need to wipe out the configuration of a previously configured access point. Cisco provides two main methods to perform a factory reseton the Aironet 1100and 1200series access pointsand these are: 1) Via theMode Button2) Via Web Interface.

How do I perform a factory reset on the Aironet 1100/1200 series?

Cisco provides two main methods to perform a factory reseton the Aironet 1100and 1200series access pointsand these are: 1) Via theMode Button2) Via Web Interface.

How do I perform a factory reset from the access point?

The access point will present a number of different management options. Here we can select the Reset to Defaultsto initiate the factory reset or alternatively the Reset to Defaults (Except IP)if we wish to reset to factory defaults but keep the current IP address.