How do I access Cisco SPA122?

Posted on by Mary Andersen

How do I access Cisco SPA122?

Procedure

  1. Using a LAN/Ethernet cable, connect the computer to the yellow Ethernet (LAN) port of the SPA122.
  2. Open Internet Explorer browser (IE is required to ensure the adapter’s configuration page displays properly).
  3. Log in: admin / (administrator password)
  4. Click Voice > Provisioning.
  5. Click Submit.

How do I reset my SPA122?

1 Reply

  1. Plug in power adapter.
  2. Plug in a phone to ‘Phone 1′ port of the SPA122.
  3. Dial ****
  4. You should hear ‘Configuration Option Menu’
  5. Dial 73738# (RESET#)
  6. Press 1 to confirm the reset.

How do I log into Cisco SPA112?

How to access the web configuration utility on the Cisco SPA112

  1. Open a web browser and enter the IP address of the phone adapter in the address bar, then press Enter.
  2. Enter the username of the device in the Username field.
  3. Enter the password of the device in the Password field.

What is the default password for Cisco IP phone?

Enter the password of the device in the Password field. The default password for the administrator is admin and for the user it is cisco. Note: If you forget the password, you can reset the phone adapter to factory defaults which in turn returns the device to the default login.

How do I log into my Cisco router?

Cisco router login:

  1. Make sure you’re connected to your network.
  2. Open a browser, and go to 192.168. 15.1.
  3. Enter the username and password.
  4. Default login credentials.
  5. Next Up: Speed up your Wi-Fi connection.

How do I default a Cisco ATA?

Dial the following IVR code using the phone keypad: 73738 (RESET) followed by the # key. The IVR will ask you to confirm by pressing the 1 on the phone keypad. You must hang-up the phone to commence the reboot sequence.

How do I log into Cisco ATA?

Enter the old password (“admin”) and then enter the new password. From a factory default baseline on a Cisco 192 ATA device, plug an Ethernet cable into to the Ethernet slot of the device. Enter this IP address into your browser 192.168. 15.1 to be prompted for login.

What is the default password on a Cisco ATA 191?

admin
Log in to the device using the default (case-sensitive) username (“admin”) and password (“admin”), and then click Log In.

How do I configure ATA 192?

Cisco ATA 191 and ATA 192

  1. Plug the ATA into your local network from the Network port.
  2. Plug a computer into the ethernet port of the ATA 192.
  3. Navigate to 192.168. 15.1 (By default this device is routing and has DHCP on for connections with the Ethernet port.
  4. Log in using admin/admin.

How do I unlock my Cisco phone 7942?

Cisco 7942

  1. Press the Settings key.
  2. Press 2 – Network.
  3. Press **# to unlock the phone.
  4. Press 7 – Admin Vlan (Virtual Local Area network) (Telephony Vlan)

What is the default username and password for the spa112/spa122?

For the SPA112/SPA122 please specify “admin” as the username, and “admin” as the password (without quotes). Once you have made your changes click on the Submit button to save your changes.

How do I connect to spa122 from my PC?

Your PC will connect via another LAN port on your router/switch (must be on same sub-net). By default, SPA122 is in NAT-Router Mode. Thus, you access it via its default router gateway IP address: 192.168.15.1, from the yellow LAN side Ethernet port, using your PC and its web browser.

How do I access spa122 in Nat mode?

By default, SPA122 is in NAT-Router Mode. Thus, you access it via its default router gateway IP address: 192.168.15.1, from the yellow LAN side Ethernet port, using your PC and its web browser.

How do I restore my SPA112 to factory default settings?

Login to the SPA112 Click on the Administration button at top of the landing page Navigate to the Factory Defaults option (located in the left side navigation menu pane) Once in the Factory Defaults option page, note that the restore option radio buttons default to No.